DIY Sheds
Plans
These are the step by step plans for the shed reference: 40ffe460-f773-11e9-b1a7-336f29933f77
DIY Sheds

Average build cost £7,910.12

The Base

Base Preperation

First you'll ..
The Tools Needed
  • tool 1
  • tool 2
  • tool 3
  • tool 4
  • tool 5
The materials needed for the base - See the cutting list for more details
  • A0 - Sawn Treated Easi Edge 225 x 75mm (9" x 3") 4.8m Kiln Dried C16 FSC x 2
  • A2 - Sawn Treated Easi Edge 225 x 75mm (9" x 3") 4.8m Kiln Dried C16 FSC x 22
  • A5 - Sawn Treated Easi Edge 225 x 75mm (9" x 3") 4.8m Kiln Dried C16 FSC x 2
  • A7 - Sawn Treated Easi Edge 225 x 75mm (9" x 3") 4.8m Kiln Dried C16 FSC x 28
  • A8 - Sawn Treated Easi Edge 225 x 75mm (9" x 3") 4.8m Kiln Dried C16 FSC x 4
  • A9 - Sawn Treated Easi Edge 225 x 75mm (9" x 3") 4.8m Kiln Dried C16 FSC x 3
  • B0 - General Purpose OSB 3 Board - 9mm X 1200mm X 2400mm x 10
  • B10 - General Purpose OSB 3 Board - 9mm X 1200mm X 2400mm x 5

The Frame

Frame with drill measurements
To start the base frame, you’ll need A0 & A6. Mark both lengths at the same time at 678mm, 1235mm.
Close up of drill holes
Pre-drill holes using a 6mm drill bit as per the drawing.
Layout the timber to match the diagram.
DIY Sheds Created by DIY Sheds A0 A5 A0 A5 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A8 A7 A7 A7 A7 A7 A7 A7 A7 A9 A8 A7 A7 A7 A7 A7 A7 A7 A7 A9 A8 A7 A7 A7 A7 A7 A7 A7 A7 A9 A8 A7 A7 A7 A7 6000mm 5000mm
Start by screwing the two end rafters to xx using XX screws. You can then check the diagonal measurements and move the frame so they’re both xx.
Then attach the remaining rafters followed by the noggins (xx). A good tip is to use the noggins as a guide on each end to get the spacing to match.
It might be easier to attach the noggins as you add each rafter so that you have more space for the drill.
Frame with all rafters
Frame with rafter and noggins

Floor Insulation

To insulate the floor you’ll need to add rails to hold the insulation in place. Use xx and screw them in place along each side of the rafters.
Push the insulation panels in place. It’s best to start from the middle so you don’t have to step on it as it will be fragile.

Floor OSB

Lay the OSB boards onto the frame and screw in place one by one using 50mm screws roughly every 300-400mm
DIY Sheds Created by DIY Sheds B0 B0 B10 B0 B0 B10 B0 B0 B10 B0 B0 B10 B0 B0 B10 6000mm 5000mm

The Walls

The materials needed for the wall frames - See the cutting list for more details
  • C0 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 19
  • C2 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 8
  • C3 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 30
  • C4 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 1
  • C5 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 1
  • C6 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 5
  • C7 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 2
  • C8 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 1
  • C9 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 1
  • C10 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 2
  • C11 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 18
  • C12 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 6
  • C13 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 1
  • C14 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 4
  • C15 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 2
  • C16 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 1
  • C17 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 1
  • C18 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 1
  • C19 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 7
  • C20 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 1
  • C21 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 1
  • C22 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 1

The Back Frame

For the base frame, you’ll need xxxx. Mark both lengths at the same time at xxmm, xxmm….
Pre-drill holes using an x drill bit as per the drawing.
Layout the timber to match the diagram.
DIY Sheds Created by DIY Sheds C0 C0 C14 C0 C0 C13 C0 C0 C14 C3 C3 C3 C3 C3 C3 C3 C3 C3 C3 C3 C3 C3 C15 C11 C11 C11 C11 C11 C11 C11 C11 C18 6010mm 2256mm
Start by screwing the two end rafters. You can then check the diagonal measurements so they are both equal.
Then attach the remaining rafters followed by the noggins. A good tip is to use the noggins as a guide on each end to get the spacing to match.
It might be easier to attach the noggins as you add each rafter so that you have more space for the drill.
plans.walls.left.join_frame

The Left Frame

Layout the timber to match the diagram.
DIY Sheds Created by DIY Sheds C0 C12 C12 C0 C0 C7 C0 C12 C12 C3 C3 C3 C3 C3 C3 C3 C3 C3 C3 C16 C11 C11 C11 C11 C11 C11 C11 4921mm 2256mm

The Right Frame

Layout the timber to match the diagram.
DIY Sheds Created by DIY Sheds C21 C8 C0 C0 C7 C0 C12 C12 C3 C3 C6 C6 C6 C6 C6 C3 C3 C3 C3 C3 C4 C5 C11 C11 C0 C9 4921mm 2256mm