
Plans
These are the step by step plans for the shed reference: 6ec07dd0-0600-11ea-935b-9bd47b69bc18
The Base
Base Preperation
First you'll ..
The Tools Needed
- tool 1
- tool 2
- tool 3
- tool 4
- tool 5
The materials needed for the base - See the cutting list for more details
- A0 - Sawn Treated Easi Edge 200 x 47mm (8" x 2") Kiln Dried C16 FSC x 2
- A3 - Sawn Treated Easi Edge 200 x 47mm (8" x 2") Kiln Dried C16 FSC x 2
- A4 - Sawn Treated Easi Edge 200 x 47mm (8" x 2") Kiln Dried C16 FSC x 14
- A6 - Sawn Treated Easi Edge 200 x 47mm (8" x 2") Kiln Dried C16 FSC x 10
- A8 - Sawn Treated Easi Edge 200 x 47mm (8" x 2") Kiln Dried C16 FSC x 2
- A9 - Sawn Treated Easi Edge 200 x 47mm (8" x 2") Kiln Dried C16 FSC x 2
- B0 - General Purpose OSB 3 Board - 9mm X 1200mm X 2400mm x 6
- B8 - General Purpose OSB 3 Board - 9mm X 1200mm X 2400mm x 3
The Frame
To start the base frame, you’ll need A0 & A6. Mark both lengths at the same time at 678mm, 1235mm.
Pre-drill holes using a 6mm drill bit as per the drawing.
Layout the timber to match the diagram.
Floor Insulation
To insulate the floor you’ll need to add rails to hold the insulation in place. Use xx and screw them in place along each side of the rafters.
Push the insulation panels in place. It’s best to start from the middle so you don’t have to step on it as it will be fragile.
Floor OSB
Lay the OSB boards onto the frame and screw in place one by one using 50mm screws roughly every 300-400mm
The Walls
The materials needed for the wall frames - See the cutting list for more details
- C0 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 16
- C2 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 14
- C3 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 1
- C4 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 1
- C5 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 1
- C6 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 1
- C7 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 27
- C8 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 7
- C9 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 2
- C10 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 1
- C11 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 5
- C12 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 2
- C13 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 4
- C14 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 6
- C15 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 15
- C16 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 4
- C17 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 1
- C18 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 2
- C19 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 1
- C20 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 2
- C21 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 1
The Back Frame
Layout the timber to match the diagram.
Start by screwing the two end rafters. You can then check the diagonal measurements so they are both equal.
Then attach the remaining rafters followed by the noggins. A good tip is to use the noggins as a guide on each end to get the spacing to match.
It might be easier to attach the noggins as you add each rafter so that you have more space for the drill.
plans.walls.left.join_frame
The Left Frame
Layout the timber to match the diagram.
The Right Frame
Layout the timber to match the diagram.
The Front Frame
Layout the timber to match the diagram.
Back Wall OSB
Lay the OSB boards onto the frame and screw in place one by one using 50mm screws roughly every 300-400mm