DIY Sheds
Plans
These are the step by step plans for the shed reference: b1139d30-f771-11e9-a908-71376d8f8f9b
DIY Sheds
Plans

Average build cost £2,681.99

The Base

Base Preperation

First you'll ..
The Tools Needed
  • tool 1
  • tool 2
  • tool 3
  • tool 4
  • tool 5
The materials needed for the base - See the cutting list for more details
  • A0 - Sawn Treated Easi Edge 150 x 47mm (6" x 2") Kiln Dried C16 FSC x 2
  • A4 - Sawn Treated Easi Edge 150 x 47mm (6" x 2") Kiln Dried C16 FSC x 9
  • A5 - Sawn Treated Easi Edge 150 x 47mm (6" x 2") Kiln Dried C16 FSC x 6
  • A7 - Sawn Treated Easi Edge 150 x 47mm (6" x 2") Kiln Dried C16 FSC x 2
  • A8 - Sawn Treated Easi Edge 150 x 47mm (6" x 2") Kiln Dried C16 FSC x 1
  • A9 - Sawn Treated Easi Edge 150 x 47mm (6" x 2") Kiln Dried C16 FSC x 1
  • B0 - General Purpose OSB 3 Board - 9mm X 1200mm X 2400mm x 4

The Frame

Frame with drill measurements
To start the base frame, you’ll need A0 & A6. Mark both lengths at the same time at 678mm, 1235mm.
Close up of drill holes
Pre-drill holes using a 6mm drill bit as per the drawing.
Layout the timber to match the diagram.
DIY Sheds Created by DIY Sheds A0 A7 A0 A7 A4 A4 A4 A4 A4 A4 A4 A4 A4 A8 A5 A5 A5 A5 A5 A5 A9 4800mm 2400mm
Start by screwing the two end rafters to xx using XX screws. You can then check the diagonal measurements and move the frame so they’re both xx.
Then attach the remaining rafters followed by the noggins (xx). A good tip is to use the noggins as a guide on each end to get the spacing to match.
It might be easier to attach the noggins as you add each rafter so that you have more space for the drill.
Frame with all rafters
Frame with rafter and noggins

Floor Insulation

To insulate the floor you’ll need to add rails to hold the insulation in place. Use xx and screw them in place along each side of the rafters.
Push the insulation panels in place. It’s best to start from the middle so you don’t have to step on it as it will be fragile.

Floor OSB

Lay the OSB boards onto the frame and screw in place one by one using 50mm screws roughly every 300-400mm
DIY Sheds Created by DIY Sheds B0 B0 B0 B0 4800mm 2400mm

The Walls

The materials needed for the wall frames - See the cutting list for more details
  • C0 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 5
  • C2 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 2
  • C3 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 1
  • C4 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 5
  • C5 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 5
  • C6 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 11
  • C7 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 1
  • C8 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 1
  • C9 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 21
  • C10 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 2
  • C11 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 2
  • C12 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 2
  • C13 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 1
  • C14 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 12
  • C15 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 1
  • C16 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 8
  • C17 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 4
  • C18 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 3
  • C19 - Treated Studwork CLS Timber - 38 x 89 x 2400 mm x 1

The Back Frame

For the base frame, you’ll need xxxx. Mark both lengths at the same time at xxmm, xxmm….
Pre-drill holes using an x drill bit as per the drawing.
Layout the timber to match the diagram.
DIY Sheds Created by DIY Sheds C0 C16 C16 C0 C4 C0 C16 C16 C9 C9 C9 C9 C9 C9 C9 C9 C9 C9 C9 C19 C14 C14 C14 C14 C14 C14 C12 4810mm 2047mm
Start by screwing the two end rafters. You can then check the diagonal measurements so they are both equal.
Then attach the remaining rafters followed by the noggins. A good tip is to use the noggins as a guide on each end to get the spacing to match.
It might be easier to attach the noggins as you add each rafter so that you have more space for the drill.
plans.walls.left.join_frame

The Left Frame

Layout the timber to match the diagram.
DIY Sheds Created by DIY Sheds C4 C2 C4 C9 C9 C9 C9 C9 C10 C14 C14 C11 2321mm 2047mm

The Right Frame

Layout the timber to match the diagram.
DIY Sheds Created by DIY Sheds C4 C2 C4 C9 C9 C9 C9 C9 C10 C14 C14 C11 2321mm 2047mm

The Front Frame

Layout the timber to match the diagram.
DIY Sheds Created by DIY Sheds C15 C13 C0 C16 C16 C0 C16 C16 C6 C6 C6 C17 C5 C17 C5 C17 C5 C17 C6 C6 C5 C5 C6 C6 C6 C6 C6 C6 C7 C8 C3 C14 C14 C12 C18 C18 C18 4810mm 2247mm

Back Wall OSB

Lay the OSB boards onto the frame and screw in place one by one using 50mm screws roughly every 300-400mm

Left Wall OSB

Right OSB

Front Wall OSB

plans.walls.back.membrane

The Roof Frame

Layout the timber to match the diagram.
DIY Sheds Created by DIY Sheds A0 A6 A0 A6 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A8 A5 A5 A5 A5 A5 A5 A5 A3 A8 A5 A5 A5 A5 A5 A5 A5 A3 5086mm 2909mm

Roof OSB

Lay the OSB boards onto the frame and screw in place one by one using 50mm screws roughly every 300-400mm
DIY Sheds Created by DIY Sheds B0 B0 B3 B0 B0 B3 B0 B0 B3 5086mm 2909mm

Back Battens

DIY Sheds Created by DIY Sheds E11 E11 E11 E11 E11 E11 E11 E11 E11 4854mm 2046mm

Left Battens

DIY Sheds Created by DIY Sheds E11 E8 E5 E3 E1 2454mm 2247mm

Right Battens

DIY Sheds Created by DIY Sheds E2 E4 E7 E10 E12 2454mm 2246mm

Front Battens

DIY Sheds Created by DIY Sheds E2 E2 E9 E13 E9 E13 E2 E2 E6 E6 E2 E2 E2 E2 E2 4854mm 2246mm
plans.walls.back.doors
plans.walls.left.doors
plans.walls.right.doors
plans.walls.front.doors
plans.walls.back.window
plans.walls.left.window
plans.walls.right.window
plans.walls.front.window
plans.back.cladding_corner_edge
plans.front.cladding_door_edge
plans.front.cladding_window_edge
plans.walls.back.cladding_bottom

Cladding

Cladding

Cladding

Cladding

plans.roof.sofits
plans.walls.back.insulation
plans.walls.back.inner_cladding
plans.walls.left.inner_cladding
plans.walls.right.inner_cladding
plans.walls.front.inner_cladding
plans.roof.inner_cladding
plans.floor.under_flooring
plans.floor.flooring
plans.floor.skirting